How to fold a simple paper plane (How to fold a simple paper plane and fly 100 meters away)

1 First, you only need to use a sheet with a side length of 15cmHow to fold a simple paper planeThis kind of aircraft is different from other aircraft. One of the special features is that the folding method of the tail paper aircraft is relatively simple. It takes a few steps to complete the folding of two diagonal sides of a square paper with a side length of 15 cm X 15cm. After folding 2, fold corner 1 towards corner 2 and align it, fold corner 3 that is stacked together in the middle towards corner 4, fold part of the top corner 5, and the corner on the back.

The folding method for a paper airplane flying far away is as follows: 1 Prepare a piece of A4 paper, place the paper horizontally to align the upper left corner of the paper to the right, and then fold it up so that the upper right corner is aligned with the lower left corner to unfold the paper. Align the upper right corner of the paper to the left, then fold it down so that the upper left corner is aligned with the lower right corner to unfold the paper. 2 Align the upper left corner of the paper to the right, then fold it down so that the upper right corner is aligned with the lower left corner to unfold the upper right of the paper.

5 As shown in the picture, insert one end into the gap at the other end and apply a little white latex to prevent it from spreading out. 6 Squater the other end, then fold it inwards for a small section. 7 Then fold it in the other direction. Open, fold it to both sides respectively. 8 Press the left part and fold it inwards, open, then rotate until it is 9 fold and the sharp corner 10 at the tail opens. A simple and fun revolving paper airplane is completedHow to fold a simple paper planeThis paper introduces the flying principles of an airplane and the flying principles of an airplane.

3 Make the tail fin on the back of the paper, leaving a width of about 1 cm, then fold it in half and fold the lower part upward along the crease to form the tail fin Adjust the angle and position of the wings and tail fin to ensure that they can fly smoothly 4 Flight test Gently throw the paper plane, let it fly into the air Pay attention to the strength and angle of the throwing, so that the paper plane maintains a stable flying attitude in the air. Combat the shape of the paper plane 1 fuselage design.

The first step is to cut a piece of A4 paper into four equal parts. The small edition uses one-quarter of the A4 paper. Fold the upper and lower long edges in half, and then unfold it to form a crease. Step 2, fold the two corners on the right side to the middle mark respectively, and the short edge overlaps with the middle mark, resulting in Figure 2. Step 3, fold the two sides of the triangle on the right side to the middle mark respectively, and the edges overlap with the mark to obtain Figure 3. Step 4, fold the right hypotenuse 1 and hypotenuse 2 in Figure 3 respectively.

How to fold a long-lost paper airplane is as follows: 1 Steps to fold a long-lost paper airplane The following is a simple step to show how to fold an airplane. Please note that this folding method may vary depending on the teaching material or origami method. Prepare a square paper, you can use ordinary printing paper or origami paper to fold the paper diagonally so that one corner is aligned with the other corner, and then unfold and fold the two opposite edges in half to make the paper one.

The folding method of a rotary aircraft is as follows: Materials: Paper: 1 First prepare a piece of A4 paper without creases, and fold it in half, as shown in the following figure. 2 Fold it at one corner and fold the other corner, as shown in the following figure. 3 Then fold it inwards., as shown in the following figure. 4 Then fold it back to the side, as shown in the following figure. 5 Fold it into two small corners, open it, as shown in the following figure. 6 Then turn the triangle up, as shown in the following figure. 7 Finally fold it in half.

1 The process of making a paper airplane is very simple. The first step is to prepare a piece of paper about the size of a math book. The second step is to fold the rectangular paper in half along the length, remember to be neat, otherwise, the airplane will not be dexterous. After unfolding, fold the two corners against the crease. Step 3, fold the folded one upwards to form a regular triangle and then fold it neatly on both sides. Finally, fold the wing and it is completed. 2 Today, my classmates and I folded the paper plane first took out a long sheet.